ASTM F593-22
Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- Standard No.
- ASTM F593-22
- Release Date
- 2022
- Published By
- American Society for Testing and Materials (ASTM)
- Latest
- ASTM F593-22
- Scope
- 1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. 1.2 Seven groups of stainless steel alloys are covered, including fourteen austenitic, two ferritic, four martensitic, and one precipitation hardening. Group AlloysA ConditionB 1 304, 305, 384, 304 L, (CW) cold workedC 18-9LW, 302HQ, 304J3D 2 316, 316 L (CW) cold workedC 3 321, 347 (CW) cold workedC 4 430E (CW) cold workedC 5 410F (H) hardened and tempered 6 431 (H) hardened and tempered 7 630 (AH) age hardened A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer (see 6.1). B See 4.2 for options. C Sizes 0.75 in. and larger may be hot worked and solution annealed, provided the bolts comply with the cold worked (CW) mechanical property requirements. D When approved by the purchaser, Alloys 303, 303Se, or XM1 may be furnished. E When approved by the purchaser, Alloy 430F may be furnished. F When approved by the purchaser, Alloys 416 or 416Se may be furnished. 1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order. 1.4 Suitable nuts for use with bolts, hex cap screws, and studs included in this specification are covered by Specification F594. Unless otherwise specified, all nuts used on these fasteners shall conform to the requirements of Specification F594, shall be of the same alloy group, and shall have a specified minimum proof stress equal to or greater than the specified minimum full-size tensile strength of the externally threaded fastener. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F593-22 Referenced Document
- ASTM A262 Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
- ASTM A276 Standard Specification for Stainless Steel Bars and Shapes
- ASTM A342/A342M Standard Test Methods for Permeability of Feebly Magnetic Materials
- ASTM A380 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
- ASTM A484/A484M Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings*， 2024-01-01 Update
- ASTM A493 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
- ASTM A555/A555M Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
- ASTM A564/A564M Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
- ASTM A582/A582M Standard Specification for Free-Machining Stainless Steel Bars
- ASTM A751 Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
- ASTM A967 Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts
- ASTM D3951 Standard Practice for Commercial Packaging
- ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
- ASTM F1470 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection*， 2024-01-26 Update
- ASTM F594 Standard Specification for Stainless Steel Nuts
- ASTM F606/F606M Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
- JIS G 4309 Stainless steel wires
ASTM F593-22 history
- 2022 ASTM F593-22 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2017 ASTM F593-17 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2013 ASTM F593-13ae1 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2013 ASTM F593-13a Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2013 ASTM F593-13 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2002 ASTM F593-02(2008)e1 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2002 ASTM F593-02(2008) Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2002 ASTM F593-02e2 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2002 ASTM F593-02e1 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2002 ASTM F593-02 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 2002 ASTM F593-01 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- 1998 ASTM F593-98 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
