ASTM F1430/F1430M-20 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
1.1 This test method describes a procedure for acoustic emission (AE) testing of aerial personnel devices (APDs) with supplemental load handling attachments.
1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted aerial personnel devices with supplemental load handling attachments:
1.1.1.1 Extensible-boom APDs,
1.1.1.2 Articulating-boom APDs, and
1.1.1.3 Any combination of
1.1.1.1 and
1.1.1.2.
1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:
1.1.2.1 Aerial personnel devices without supplemental load handling attachments,
1.1.2.2 Digger-derricks with platform,
1.1.2.3 Cranes with platform, and
1.1.2.4 Aerial devices with load-lifting capabilities located anywhere other than adjacent to the platform. NOTE 1—This test method is not intended to be a stand-alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.
1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. (Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test. During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle or components.)
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F1430/F1430M-20 Referenced Document
ANSI A92.2 Vehicle-Mounted Elevating and Rotating Aerial Devices*, 2024-04-22 Update
ASTM E114 Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Examination by the Contact Method
ASTM E1316 Standard Terminology for Nondestructive Examinations*, 2024-02-01 Update
ASTM E1417/E1417M Standard Practice for Liquid Penetrant Testing*, 2021-09-01 Update
ASTM E1444/E1444M Standard Practice for Magnetic Particle Testing for Aerospace*, 2022-07-01 Update
ASTM E164 Standard Practice for Ultrasonic Contact Examination of Weldments
ASTM E569 Standard Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation
ASTM E650 Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors
ASTM E750 Standard Practice for Characterizing Acoustic Emission Instrumentation
ASTM E94 Standard Guide for Radiographic Examination*, 2024-04-22 Update
ASTM E976 Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response*, 2021-11-01 Update
ASTM F2174 Standard Practice for Verifying Acoustic Emission Sensor Response*, 2023-06-09 Update
ASTM F914 Standard Test Method for Acoustic Emission for Insulated Aerial Personnel Devices
ASTM F1430/F1430M-20 history
2020ASTM F1430/F1430M-20 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
2018ASTM F1430/F1430M-18 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
2015ASTM F1430/F1430M-15 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
2014ASTM F1430/F1430M-14 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
2010ASTM F1430/F1430M-10 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
2003ASTM F1430-03e1 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
2003ASTM F1430-03 Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
1998ASTM F1430-98 Standard Test Method for Acoustic Emission Testing of Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments