1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best fit cleaning agent and process. This guide takes into account environmental pollution prevention factors in a selection process.
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the cleaning material selection process, calling for engineers to customize their selection based on the cleaning requirements for the cleaning tasks at hand. If a part can be cleaned, and kept clean, it can be cycled through several process steps that have cleaning requirements. This eliminates extra cleaning process steps during the total process. A total life cycle cost analysis or performance/cost of ownership study is recommended to compare the methods available.
1.3 This guide is for general industry manufacturing, equipment maintenance and remanufacturing operations, and to some extent precision cleaning of mechanical parts and assemblies. It is not intended to be used for optical, medical, or electronics applications, nor is it intended for dry-cleaning or super-critical fluid cleaning.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D6361/D6361M-98(2020) Referenced Document
ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*, 2024-04-22 Update
ASTM D3167 Standard Test Method for Floating Roller Peel Resistance of Adhesives
ASTM D3278 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D3519 Standard Test Method for Foam in Aqueous Media (Blender Test)
ASTM D3601 Standard Test Method for Foam In Aqueous Media (Bottle Test)
ASTM D3707 Standard Test Method for Storage Stability of Water-in-Oil Emulsions by the Oven Test Method
ASTM D3709 Standard Test Method for Stability of Water-in-Oil Emulsions Under Low to Ambient Temperature Cycling Conditions
ASTM D3762 Standard Test Method for Adhesive-Bonded Surface Durability of Aluminum (Wedge Test)
ASTM D56 Standard Test Method for Flash Point by Tag Closed Tester
ASTM D92 Standard Test Method for Flash and Fire Points by Cleveland Open Cup
ASTM D93 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM E1720 Standard Test Method for Determining Ready, Ultimate, Biodegradability of Organic Chemicals in a Sealed Vessel CO2 Production Test
ASTM E70 Standard Test Method for pH of Aqueous Solutions With the Glass Electrode
ASTM F1104 Standard Test Method for Preparing Aircraft Cleaning Compounds, Liquid Type, Water Base, for Storage Stability Testing
ASTM F1110 Standard Test Method for Sandwich Corrosion Test
ASTM F1111 Standard Test Method for Corrosion of Low-Embrittling Cadmium Plate by Aircraft Maintenance Chemicals
ASTM F483 Standard Test Method for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals
ASTM F484 Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds
ASTM F485 Standard Test Method for Effects of Cleaners on Unpainted Aircraft Surfaces
ASTM F502 Standard Test Method for Effects of Cleaning and Chemical Maintenance Materials on Painted Aircraft Surfaces
ASTM F519 Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating Processes and Service Environments
ASTM F945 Standard Test Method for Stress-Corrosion of Titanium Alloys by Aircraft Engine Cleaning Materials
ASTM G121 Standard Practice for Preparation of Contaminated Test Coupons for the Evaluation of Cleaning Agents
ASTM G122 Standard Test Method for Evaluating the Effectiveness of Cleaning Agents
ASTM G44 Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5?% Sodium Chloride Solution