UL 60745-1 BULLETIN-2009 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: March 30@ 2009)
This International Standard deals with the safety of hand-held motor-operated or magnetically driven electric tools@ the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools@ and 440 V for three-phase a.c. tools.So far as is practicable@ this standard deals with the common hazards presented by hand-held tools@ which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools.Tools with an electric heating element are within the scope of this standard. They should also comply with relevant parts of IEC 60335.Hand-held electric tools@ hereinafter referred to as tools@ which can be mounted on a support for use as fixed tools without any alteration of the tool itself@ are within the scope of this standard. Unless the requirement for such support is given in a relevant part 2@ this standard alone will not be sufficient to ensure that the combination of tool and support is adequate.Requirements for motors not isolated from the supply@ and having basic insulation not designed for the rated voltage of the tools@ are given in Annex B. Requirements for rechargeable battery- powered motor-operated or magnetically driven tools and the battery packs for such tools are given in Annex K. Those for such tools that are also operated and/or charged directly from the mains or a non-isolated source are given in Annex L.This standard does not apply to:?C hand-held tools intended to be used in the presence of explosive atmosphere (dust@ vapour or gas);?C hand-held tools used for preparing and processing food;?C?hand-held tools for medical purposes (IEC 60601);?C?heating tools which are covered by IEC 60335-2-45.For hand-held tools intended to be used in vehicles or on board ships or aircraft@ additional requirements may be necessary.For hand-held tools intended to be used in tropical countries@ special requirements may be necessary.NOTE Attention is drawn to the fact that in many countries@ additional requirements are specified by the national health authorities@ the national authorities responsible for the protection of labour@ the national water supply authorities@ etc.?
UL 60745-1 BULLETIN-2009 history
1970UL 60745-1-2022 National Differences For Hand-Held Motor-Operated Electric Tools �C Safety �C Part 2-5: Particular Requirements for Circular Saws
1970UL 60745-1-2020 National Differences For Hand-Held Motor-Operated Electric Tools �C Safety �C Part 2-5: Particular Requirements for Circular Saws (Fifth Edition; Reprint with Revisions Through and Including May 24@ 2017)
2018UL 60745-1 BULLETIN-2018 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: October 29@ 2018)
2015UL 60745-1 BULLETIN-2015 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: July 27@ 2015)
2014UL 60745-1 BULLETIN-2014 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: January 26@ 2014)
2013UL 60745-1 BULLETIN-2013 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: July 15@ 2013)
2012UL 60745-1 BULLETIN-2012 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: December 17@ 2012)
2011UL 60745-1 BULLETIN-2011 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: April 28@ 2011)
2010UL 60745-1 CRD-2010 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Section / Paragraph Reference: Clause 23.1.10 and Annex I Supersedes prior Certification Requirement Decision issued 2005-09-15 (Edition 3: July 31@ 2007)
2010UL 60745-1 BULLETIN-2010 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: September 06@ 2010)
2009UL 60745-1 CRD-2009 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Section / Paragraph Reference: 23 and Annex I Subject: Switches (Edition 4: July 31@ 2007)
2009UL 60745-1 BULLETIN-2009 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: March 30@ 2009)
2008UL 60745-1 CRD-2008 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements - Section / Paragraph Reference: 18.10@ K.23.1.10 Subject: Electronic switches - “Dangerous Malfunction” and Breaking Capacity (Edition 4: July 31@ 2007
2008UL 60745-1 BULLETIN-2008 UL Standard for Safety Hand-Held Motor-Operated Electric Tools ?Safety ?Part 1: General Requirements COMMENTS DUE: March 10, 2008
2007UL 60745-1 BULLETIN-2007 UL Standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (COMMENTS DUE: May 21@ 2007)
2007UL 60745-1 (ND)-2007 National Differences For UL 60745-1 Hand-Held Motor-Operated Electric Tools - Safety - Part 1: General Requirements (Fourth Edition; Reprint with Revisions Through and Including January 13@ 2010)
2007UL 60745-1-2007 UL Standard for Safety Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (Fourth Edition; Reprint with Revisions through and Including March 15@ 2011)
2006UL 60745-1 BULLETINS-2006 UL Standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (12/22/2006 (42p); 11/01/2006 (4p); 09/01/2006 (40p))
2004UL 60745-1 BULLETINS-2004 UL Standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (10/14/2004 (12p); 09/27/2004 (12p))
2004UL 60745-1-2004 UL Standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements (Third Edition; Reprint with Revisions Through and Including April 25@ 2005)