ASTM B200-22
Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys

Standard No.

ASTM B200-22

Release Date

2022

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM B200-22

Scope

1.1 This specification covers the requirements for electrodeposited coatings of lead and lead-tin alloys on steel and ferrous alloys. The coatings of lead-tin alloys are those that range in tin content up to, but not exceeding, 15 mass %. The coatings ranging between 3 and 15 mass % in tin content are known also as “terne” metallic electrodeposits. 1.2 This specification does not apply to sheet, strip, or wire in the unfabricated form. 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B200-22 Referenced Document

• ASTM B117 Standard Practice for Operating Salt Spray (Fog) Apparatus
• ASTM B183 Standard Practice for Preparation of Low-Carbon Steel for Electroplating
• ASTM B242 Standard Guide for Preparation of High-Carbon Steel for Electroplating
• ASTM B320 Standard Practice for Preparation of Iron Castings for Electroplating
• ASTM B322 Standard Guide for Cleaning Metals Prior to Electroplating
• ASTM B339 Standard Specification for Pig Tin
• ASTM B374 Standard Terminology Relating to Electroplating
• ASTM B487 Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
• ASTM B499 Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals
• ASTM B504 Standard Test Method for Measurement of Thickness of Metallic Coatings by the Coulometric Method*， 2023-05-01 Update
• ASTM B507 Standard Practice for Design of Articles to Be Electroplated on Racks
• ASTM B567 Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method*， 2024-04-22 Update
• ASTM B568 Standard Test Method for Measurement of Coating Thickness by X-Ray Spectrometry
• ASTM B571 Standard Practice for Qualitative Adhesion Testing of Metallic Coatings
• ASTM B602 Standard Test Method for Attribute Sampling of Metallic and Inorganic Coatings
• ASTM B697 Standard Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings
• ASTM B849 Standard Specification for Pre-Treatments of Iron or Steel for Reducing Risk of Hydrogen Embrittlement
• ASTM B850 Standard Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement

ASTM B200-22 history

• 2022 ASTM B200-22 Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys
• 1985 ASTM B200-85(2015) Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys
• 1985 ASTM B200-85(2009) Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys
• 2004 ASTM B200-85(2004) Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys
• 1985 ASTM B200-85(1999) Standard Specification for Electrodeposited Coatings of Lead and Lead-Tin Alloys on Steel and Ferrous Alloys