ASTM G210-13(2018)
Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus
- Standard No.
- ASTM G210-13(2018)
- Release Date
- 2018
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM G210-13(2023)
- Latest
- ASTM G210-13(2023)
- Scope
- 1.1 This practice covers the basic apparatus, procedures, and conditions required to create and maintain the severe wastewater analysis testing apparatus used for testing a protective coating or lining. 1.2 This apparatus may simulate the pertinent attributes of a typical domestic severe wastewater headspace (sewer) environment. The testing chamber comprises two phases: (1) a liquid phase containing a prescribed acid and saline solution, and (2) a vapor phase consisting of air, humidity, and concentrated sewer gas (Note 1). The temperature of the test chamber is elevated to create accelerated conditions and reaction rates. NOTE 1—For the purposes of this practice, sewer gas is composed of hydrogen sulfide, carbon dioxide, and methane gas. 1.3 Caution—This practice can be extremely hazardous. All necessary precautions need to be taken when working with sewer gas, sulfuric acid, and a glass tank. It is highly recommended that a professional testing laboratory experienced in testing with hydrogen sulfide, carbon dioxide, and methane gases perform this practice. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 8 on Hazards. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM G210-13(2018) Referenced Document
- ASTM A36/A36M Standard Specification for Carbon Structural Steel
- ASTM C307 Standard Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts, and Monolithic Surfacings
- ASTM C387/C387M Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar*， 2023-06-01 Update
- ASTM C580 Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes
- ASTM D2370 Standard Test Method for Tensile Properties of Organic Coatings
- ASTM D4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
- ASTM D610 Standard Test Method for Evaluating Degree of Rusting on Painted Steel Surfaces
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM D660 Standard Test Method for Evaluating Degree of Checking of Exterior Paints*， 2019-10-01 Update
- ASTM D661 Standard Test Method for Evaluating Degree of Cracking of Exterior Paints*， 2019-10-01 Update
- ASTM D6677 Standard Test Method for Evaluating Adhesion by Knife*， 2022-12-01 Update
- ASTM D7091 Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals*， 2022-06-01 Update
- ASTM D714 Standard Test Method for Evaluating Degree of Blistering of Paints
- ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-22 Update
- ASTM G193 Standard Terminology and Acronyms Relating to Corrosion*， 2022-08-01 Update
- ISO 16773 Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 4: Examples of spectra of polymer-coated and uncoated specimens
ASTM G210-13(2018) history
- 2023 ASTM G210-13(2023) Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus
- 2018 ASTM G210-13(2018) Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus
- 2013 ASTM G210-13 Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus
