1.1 This specification2 covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1). NOTE 1—Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M, low-alloy steel castings by Specification A217/A217M, and duplex stainless steel castings by Specification A995/A995M.
1.2 A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both.
1.2.1 Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800 °F [425 °C].
1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4.1 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M-specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A351/A351M-18e1 Referenced Document
ASTM A216/A216M Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature Service
ASTM A217/A217M Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
ASTM A488/A488M Standard Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel
ASTM A703/A703M Standard Specification for Steel Castings, General Requirements, for Pressure-Containing Parts
ASTM A985/A985M Standard Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts*, 2024-04-22 Update
ASTM A995/A995M Standard Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts
ASTM A351/A351M-18e1 history
2018ASTM A351/A351M-18e1 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2018ASTM A351/A351M-18 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2016ASTM A351/A351M-16 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2015ASTM A351/A351M-15 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2014ASTM A351/A351M-14 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2013ASTM A351/A351M-13a Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2013ASTM A351/A351M-13 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2012ASTM A351/A351M-12b Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2012ASTM A351/A351M-12a Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2012ASTM A351/A351M-12 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2010ASTM A351/A351M-10 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2006ASTM A351/A351M-06 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
2005ASTM A351/A351M-05 Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts
2003ASTM A351/A351M-03 Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts
2000ASTM A351/A351M-00 Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts
1994ASTM A351/A351M-94 Standard Specification for Castings, Austenitic, Austenitic- Ferritic (Duplex), for Pressure-Containing Parts