ASTM A907/A907M-96
Standard Specification for Steel, Sheet and Strip, Heavy Thickness Coils, Carbon, Hot-Rolled, Structural Quality

Standard No.

ASTM A907/A907M-96

Release Date

1970

Published By

/

Status

Withdraw 2001-01

Latest

ASTM A907/A907M-96

Scope

1.1 This specification covers hot-rolled heavy-thickness carbon-steel sheet and strip of structural quality in coils beyond the size limits of Specification A 570/A 570M. This material is intended for structural purposes where mechanical test values are required and is available in the sizes listed below. This material is available only in coils as described below: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip over 8 to 12 (200 to 300) 0.230 to 1.000, incl (6.0 to 25) Sheet over 12 to 48 (300 to 1200) 0.230 to 1.000, incl (6.0 to 25) over 48 (1200) 0.180 to 1.000, incl (4.5 to 25) 1.1.1 The following grades are covered in this specification: Mechanical Properties Grade Yield Point min, ksi (MPa) Tensile Strength min, ksi (MPa) 30 30 (205) 49 (340) 33 33 (230) 52 (360) 36 36 (250) 53 (365) 40 40 (275) 55 (380) 1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values of the two systems may result in nonconformance with this specification. 1.3 Sheet and strip in coils of the sizes noted in 1.1 can be included in this specification only with the following provisions: 1.3.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A 6/A 6M (plates provided from coils) or A 20/A 20M (plates produced from coils), 1.3.2 This specification is not applicable to the steels covered by Specification A 635/A 635M, 1.3.3 The dimensional tolerances from Specification A 635/ A 635M are applicable to material produced in accordance with this specification, 1.3.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming, and 1.3.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations.

ASTM A907/A907M-96 Referenced Document

• ASTM A20/A20M Standard Specification for General Requirements for Steel Plates for Pressure Vessels*， 1997-04-22 Update
• ASTM A570/A570M Standard Specification for Steel, Sheet and Strip, Carbon, Hot-Rolled (Withdrawn 2000)*， 2021-02-18 Update
• ASTM A6/A6M Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling*， 2024-03-01 Update
• ASTM A635/A635M Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General*， 2022-09-01 Update
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications*， 1993-04-22 Update

ASTM A907/A907M-96 history

• 1970 ASTM A907/A907M-96 Standard Specification for Steel, Sheet and Strip, Heavy Thickness Coils, Carbon, Hot-Rolled, Structural Quality