ASTM F1743-22
Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)

Standard No.

ASTM F1743-22

Release Date

2022

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F1743-22

Scope

1.1 This practice describes the procedures for the reconstruction of pipelines and conduits (2 in. to 96 in. (5 cm to 244 cm) diameter) by the pulled-in-place installation of a resinimpregnated, flexible fabric tube into an existing conduit and secondarily inflated through the inversion of a calibration hose by the use of a hydrostatic head or air pressure (see Fig. 1). The resin is cured by circulating hot water, by the introduction of controlled steam into the tube, or by photoinitiated reaction. When cured, the finished cured-in-place pipe will be continuous and tight fitting. This reconstruction process may be used in a variety of gravity and pressure applications such as sanitary sewers, storm sewers, process piping, electrical conduits, and ventilation systems. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 1—There are no ISO standards covering the primary subject matter of this practice. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F1743-22 Referenced Document

• ASTM C1920 Standard Practice for Cleaning of Vitrified Clay Sanitary Sewer Pipelines*， 2023-10-01 Update
• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D1682 
• ASTM D3039/D3039M Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
• ASTM D3567 Standard Practice for Determining Dimensions of ldquo;Fiberglassrdquo; (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
• ASTM D4814 Standard Specification for Automotive Spark-Ignition Engine Fuel
• ASTM D543 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
• ASTM D5813 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Pipe
• ASTM D638 Standard Test Method for Tensile Properties of Plastics
• ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-22 Update
• ASTM D903 Standard Test Method for Peel or Stripping Strength of Adhesive Bonds
• ASTM E797 Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method
• ASTM F1216 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
• ASTM F412 Standard Terminology Relating to Plastic Piping Systems*， 2023-07-20 Update

ASTM F1743-22 history

• 2022 ASTM F1743-22 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• 2021 ASTM F1743-21 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• 2017 ASTM F1743-17 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• 2008 ASTM F1743-08(2016) Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• 2008 ASTM F1743-08 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• 1996 ASTM F1743-96(2003) Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• 1996 ASTM F1743-96 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)