ASTM F3506-21e1
Standard Specification for Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe based on Inner Diameter (I

Standard No.

ASTM F3506-21e1

Release Date

2021

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F3506-21e1

Scope

1.1 This specification covers a coextruded polyethylene composite pressure pipe with a butt welded aluminum tube reinforcement between the inner and outer layers. The inner and outer polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is a system of nomenclature for the polyethylene-aluminum-polyethylene of raised temperature (PE-RT/AL/PE-RT) pipes, the requirements and test methods for materials, the dimensions and strengths of the component tubes and finished pipe, adhesion tests, and the burst and sustained pressure performance. Also given are the requirements and methods of marking. The pipe covered by this specification is intended for use in air conditioning and refrigeration (ACR) line set systems. 1.2 This specification relates only to composite pipes incorporating a butt welded aluminum tube having both internal and external polyethylene layers. The welded aluminum tube is capable of sustaining internal pressures. Pipes consisting of metallic layers not butt welded together and plastic layers other than polyethylene are outside the scope of this specification. 1.3 The dimensions in this specification are ID controlled to match that of ACR Copper Tube so that the flowrate and volume remains the same on a size-for-size basis. 1.4 Specifications for fittings for use with pipe meeting the requirements of this specification are given in Annex A1. 1.5 This specification excludes crosslinked polyethylenealuminum-crosslinked polyethylene pipes (see Specification F1281). 1.6 This specification tests the pipe for service at 60 °C 6 2 °C (140 °F 6 3 °F) or 82 °C 6 2 °C (180 °F 6 3 °F). 1.7 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F3506-21e1 Referenced Document

• ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
• ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
• ASTM D2837 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
• ASTM D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials*， 2024-04-22 Update
• ASTM D3895 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
• ASTM D618 Standard Practice for Conditioning Plastics for Testing*， 2021-07-15 Update
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials*， 2024-01-01 Update
• ASTM F1281 Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe*， 2024-02-01 Update
• ASTM F412 Standard Terminology Relating to Plastic Piping Systems*， 2023-07-20 Update

ASTM F3506-21e1 history

• 2021 ASTM F3506-21e1 Standard Specification for Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe based on Inner Diameter (I
• 2021 ASTM F3506-21 Standard Specification for Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe based on Inner Diameter (ID) for use in Air Conditioning and Refrigeration Lin