ASTM D6412/D6412M-99(2020)
Standard Specification for Epoxy (Flexible) Adhesive For Bonding Metallic And Nonmetallic Materials
- Standard No.
- ASTM D6412/D6412M-99(2020)
- Release Date
- 2020
- Published By
- American Society for Testing and Materials (ASTM)
- Latest
- ASTM D6412/D6412M-99(2020)
- Scope
- 1.1 The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can withstand environmental exposure to temperatures from –184 to 82 °C [–300 to 180 °F] when exposed to an expected combination of stress, temperature, and relative humidity to be encountered in service. NOTE 1—When coordinated through the Department of Defense (DoD) and the National Aeronautics and Space Administration (NASA), this practice will be a direct replacement of MIL-A-82720 (OS), MIS-26872, and MSFC-SPEC-2037. 1.2 The values stated in SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D6412/D6412M-99(2020) Referenced Document
- ASTM A109/A109M Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
- ASTM A167 Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip
- ASTM B209 Standard Specification for Aluminum and Aluminum- Alloy Sheet and Plate
- ASTM D1002 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
- ASTM D1876 Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)*， 2023-05-17 Update
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-22 Update
- ASTM D2393 Test Method for Viscosity of Epoxy Resins and Related Components
- ASTM D2651 Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding
- ASTM D3951 Standard Practice for Commercial Packaging
- ASTM D4142 Standard Guide for Testing Epoxy Resins*， 2022-06-01 Update
- ASTM D907 Standard Terminology of Adhesives*， 2023-05-16 Update
- ASTM E595 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
ASTM D6412/D6412M-99(2020) history
- 2020 ASTM D6412/D6412M-99(2020) Standard Specification for Epoxy (Flexible) Adhesive For Bonding Metallic And Nonmetallic Materials
- 1999 ASTM D6412/D6412M-99(2012) Standard Specification For Epoxy (Flexible) Adhesive For Bonding Metallic And Nonmetallic Materials
- 1999 ASTM D6412/D6412M-99(2005) Standard Specification for Epoxy (Flexible) Adhesive for Bonding Metallic and Nonmetallic Materials
- 1999 ASTM D6412/D6412M-99 Standard Specification for Epoxy (Flexible) Adhesive for Bonding Metallic and Nonmetallic Materials
