1.1 This specification covers annealed aluminum and aluminum-alloy foil containing 98.00 % minimum aluminum and in thicknesses
0.00025 in. (0.0064 mm) to, but not including,
0.006 in. (0.15 mm). Alloys (see Note 1) covered by this specification include, but are not limited to 1100, 1145, 1235, 8011, 8079, and 8111, which conform to the requirements of
6.1 and Table 1. Unless otherwise specified by the purchaser, the alloy to be supplied shall be left to the discretion of the producer.
1.2 The foil is for use in packaging, which includes food handling and processing applications, requiring flexible barrier materials, and other general applications. The foil may be used as supplied or laminated to other materials, such as paper or plastic films.
1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are for information only.
1.5 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. NOTE 2—If the alloy is specified by the purchaser, its designation shall be in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those shown in
1.1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B479-19 Referenced Document
ASTM B926 Standard Method for Pinhole Determination in Aluminum and Aluminum Alloy Plain Foil by Means of a Light Table*, 2024-04-22 Update
ASTM E1251 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge
ASTM E252 Standard Test Method for Thickness of Thin Foil and Film by Weighing
ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM E3061 Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method)*, 2024-04-22 Update
ASTM E345 Standard Test Methods of Tension Testing of Metallic Foil
ASTM E55 Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
ASTM E607 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique, Nitrogen Atmosphere
ASTM E716 Standard Practices for Sampling Aluminum and Aluminum Alloys for Spectrochemical Analysis
ASTM E96/E96M Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials*, 2024-03-01 Update
ASTM B479-19 history
2019ASTM B479-19 Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications
2006ASTM B479-06 Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications
2000ASTM B479-00 Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications