ETSI EN 301 489-1:2016
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the Directive 2014/30/EU; P

Standard No.

ETSI EN 301 489-1:2016

Release Date

2016

Published By

ETSI - European Telecommunications Standards Institute

Status

Be replaced 2017-03

Replace By

ETSI EN 301 489-1:2017

Latest

ETSI EN 301 489-1:2019

Scope

The present document contains the common requirements for radio equipment and associated ancillary equipment@ excluding broadcast receivers@ in respect of ElectroMagnetic Compatibility (EMC). Product dependent arrangements necessary to perform the EMC tests on dedicated types of radio communications equipment@ and the assessment of test results@ are detailed in the appropriate product related parts of ETSI EN 301 489 series [i.13]. The present document@ together with the product related part@ where required@ specifies the applicable EMC tests@ the methods of measurement@ the limits and the performance criteria for radio equipment and associated ancillary equipment. In case of differences (for instance concerning special conditions@ definitions@ abbreviations) between part 1 of ETSI EN 301 489 series [i.13] and the relevant product related part of ETSI EN 301 489 series [i.13]@ the product related part takes precedence. Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port of radio equipment and combinations of radio and associated ancillary equipment are not included in the present document. Such technical specifications are normally found in the relevant product standards for the effective use of the radio spectrum. The environment classification used in the present document refers to the environment classification used in: ? CENELEC EN 61000-6-3 [i.4] and CENELEC EN 61000-6-1 [i.5] for the residential@ commercial and light industrial environment; or ? CENELEC EN 61000-6-2 [i.15] and CENELEC EN 61000-6-4 [i.14] for the industrial environment; or ? ETSI TR 101 651 [i.6] for the telecommunication centre environment; or ? ISO 7637-2 [8] for the vehicular environment. The EMC requirements have been selected to ensure an adequate level of compatibility for equipment intended to be used in the environments mentioned above. The levels@ however@ do not cover extreme cases which may occur in any location but with low probability of occurrence. The present document may not cover those cases where a potential source of interference which is producing individually repeated transient phenomena or a continuous phenomenon is permanently present@ e.g. a radar or broadcast site in the near vicinity. In such a case it may be necessary to use special protection applied to either the source of interference or the interfered part or both. Where none of the existing specific product related radio parts covers the required conditions for a particular radio equipment/service e.g. in case of the initial introduction of a new radio service or a special application@ the present document can be used for the purposes of testing to the EMC requirements set out in the present document In all cases where a radio product falls within the scope of a specific product related radio part of the standard@ the product related part takes precedence. Compliance of radio equipment to the requirements of the present document does not signify compliance to any requirements related to spectrum management or to the use of the equipment (licensing requirements). Compliance to the requirements of the present document does not signify compliance to any safety requirements. However@ it is the responsibility of the assessor of the equipment to record in the test report any observations regarding the test sample becoming dangerous or unsafe as a result of the application of the tests called for in the present document. NOTE 1: Requirements for Harmonics and flicker and voltage fluctuations are to be found in other harmonised standards. NOTE 2: The present document does not yet fully address the industrial environment and industrial equipment@ including ISM equipment. These will be addressed in a future edition.

ETSI EN 301 489-1:2016 history

• 2019 ETSI EN 301 489-1:2019 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for ElectroMagnetic Compatibility
• 2017 ETSI EN 301 489-1:2017 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of artic
• 2016 ETSI EN 301 489-1:2016 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the Directive 2014/30/EU; P
• 2011 ETSI EN 301 489-1:2011 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.9.2)
• 2008 ETSI EN 301 489-1:2008 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.8.1)
• 2007 ETSI EN 301 489-1:2007 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.7.1)
• 2006 ETSI EN 301 489-1:2006 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.7.1)
• 2005 ETSI EN 301 489-1:2005 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.6.1)
• 2004 ETSI EN 301 489-1:2004 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.6.1)
• 2003 ETSI EN 301 489-1:2003 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.5.1)
• 2002 ETSI EN 301 489-1:2002 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements (V1.4.1)
• 2001 ETSI EN 301 489-1:2001 Electromagnetic Compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 1: Common Technical Requirements (V1.3.1)
• 2000 ETSI EN 301 489-1:2000 Electromagnetic Compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 1: Common Technical Requirements (V1.2.1)
• 1999 ETSI EN 301 489-1:1999 Electromagnetic Compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 1: Common Technical Requirements (V1.1.1)