ASTM B152/B152M-19
Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

Standard No.

ASTM B152/B152M-19

Release Date

2019

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM B152/B152M-19

Scope

1.1 This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers. Copper UNS No.A Previous Designation Type of Copper C10100B OFE Oxygen-free electronic C10200B OF Oxygen-free without residual deoxidants C10300 OFXLP Oxygen-free extra low phosphorus C10400, C10500, C10700 OFS Oxygen-free, silver bearing C10800 OFLP Oxygen-free low phosphorus C10910 ... Low oxygen C11000B, C ETP, TPC Electrolytic tough pitch,C Tough pitchC C11300, C11400, C11600B STP Silver bearing tough pitch C12000 DLP Phosphorized, low residual phosphorus C12200B DHP Phosphorized, high residual phosphorus C12300 DHPS Phosphorized, silver bearing C14200 DPA Phosphorus deoxidized, arsenical C14420 ... Tin bearing tellurium copper C14530 ... Tin tellurium bearing copper A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these types of copper are classified in Classification B224. B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper UNS No. C12200. C Unless specified in the contract or purchase order the supplier is permitted to provide ETP copper or TP copper. NOTE 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application. NOTE 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in Specification B370. Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272. 1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers. 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B152/B152M-19 Referenced Document

• ASTM B170 Standard Specification for Oxygen-Free Electrolytic Copper Refinery Shapes*， 2024-04-21 Update
• ASTM B193 Standard Test Method for Resistivity of Electrical Conductor Materials
• ASTM B216 Standard Specification for Tough-Pitch Fire-Refined Copper8212;Refinery Shapes
• ASTM B224 Standard Classification of Coppers
• ASTM B248 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
• ASTM B248M Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip and Rolled Bar [Metric]
• ASTM B272 Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
• ASTM B370 Standard Specification for Copper Sheet and Strip for Building Construction
• ASTM B577 Standard Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
• ASTM B846 Standard Terminology for Copper and Copper Alloys
• ASTM E112 Standard Test Methods for Determining Average Grain Size
• ASTM E3 Standard Practice for Preparation of Metallographic Specimens
• ASTM E478 Standard Test Methods for Chemical Analysis of Copper Alloys
• ASTM E53 Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
• ASTM E62 Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials*， 2024-01-01 Update

ASTM B152/B152M-19 history

• 2019 ASTM B152/B152M-19 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 2013 ASTM B152/B152M-13 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 2009 ASTM B152/B152M-09 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 2006 ASTM B152/B152M-06ae1 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 2006 ASTM B152/B152M-06a Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 2006 ASTM B152/B152M-06 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 2000 ASTM B152/B152M-00 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 1997 ASTM B152-97a Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• 1997 ASTM B152-97 Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar