ASTM D5889/D5889M-18(2022)
Standard Practice for Quality Control of Geosynthetic Clay Liners

Standard No.
ASTM D5889/D5889M-18(2022)
Release Date
2022
Published By
American Society for Testing and Materials (ASTM)
Latest
ASTM D5889/D5889M-18(2022)
Scope
1.1 This practice covers the manufacturing quality control of geosynthetic clay liners (GCLs), describing types of tests, the proper test methods, and the minimum testing frequencies. 1.2 This practice is intended to aid manufacturers, suppliers, purchasers, and users of GCLs in establishing a minimum level of effort for manufacturing quality control. 1.3 This practice does not address manufacturing quality assurance, product acceptance testing, or conformance testing. These are independent activities taken by organizations other than the GCL manufacturer. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D5889/D5889M-18(2022) Referenced Document

  • ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique
  • ASTM D4439 Standard Terminology for Geosynthetics*， 2024-02-01 Update
  • ASTM D4632/D4632M Standard Test Method for Grab Breaking Load and Elongation of Geotextiles*， 2023-05-01 Update
  • ASTM D5199 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics*， 2024-04-21 Update
  • ASTM D5261 Standard Test Method for Measuring Mass per Unit Area of Geotextiles
  • ASTM D5887/D5887M Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter*， 2023-11-01 Update
  • ASTM D5890 Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners
  • ASTM D5891/D5891M Standard Test Method for Fluid Loss of Clay Component of Geosynthetic Clay Liners
  • ASTM D5993 Standard Test Method for Measuring Mass Per Unit of Geosynthetic Clay Liners
  • ASTM D5994/D5994M Standard Test Method for Measuring Core Thickness of Textured Geomembranes
  • ASTM D6243/D6243M Standard Test Method for Determining the Internal and Interface Shear Strength of Geosynthetic Clay Liner by the Direct Shear Method
  • ASTM D6496/D6496M Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners*， 2023-05-15 Update
  • ASTM D6693/D6693M Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
  • ASTM D6768/D6768M Standard Test Method for Tensile Strength of Geosynthetic Clay Liners
  • ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
  • ASTM D882 Standard Test Method for Tensile Properties of Thin Plastic Sheeting

ASTM D5889/D5889M-18(2022) history

Standard Practice for Quality Control of Geosynthetic Clay Liners


Copyright ©2024 All Rights Reserved