ASTM A1073/A1073M-17
Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
- Standard No.
- ASTM A1073/A1073M-17
- Release Date
- 2017
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM A1073/A1073M-21
- Latest
- ASTM A1073/A1073M-21
- Scope
- 1.1 This practice defines procedures for measuring the thickness of uncoated steel sheet and nonmetallic and metalliccoated steel sheet. Thickness is a significant quality characteristic of steel sheet products. The ability to accurately measure thickness using hand micrometers is critical in determining product conformance to specifications. The methods described are designed and intended for use in both laboratory and plant situations and their environments. 1.2 The flat steel product shall conform to all the requirements of the appropriate specifications as follows: Specifications A109/A109M, A505, A568/A568M, A635/A635M, A684/A684M, and A924/A924M. 1.3 Quantitative limits are not addressed and are established in the general requirements, or individual product specifications, or both; or when applicable, as agreed to between supplier and user. 1.4 This specification is applicable to orders in either inch-pound units or SI units. Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A1073/A1073M-17 Referenced Document
- ASTM A109/A109M Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
- ASTM A505 Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
- ASTM A568/A568M Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for*， 2019-11-01 Update
- ASTM A635/A635M Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General*， 2022-09-01 Update
- ASTM A684/A684M Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled
- ASTM A902 Standard Terminology Relating to Metallic Coated Steel Products
- ASTM A924/A924M Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
ASTM A1073/A1073M-17 history
- 2021 ASTM A1073/A1073M-21 Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
- 2017 ASTM A1073/A1073M-17 Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
- 2016 ASTM A1073/A1073M-16 Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
- 2014 ASTM A1073/A1073M-14 Standard Practice for Using Hand Micrometers to Measure the Thickness of Nonmetallic and Metallic-Coated Steel Sheet
- 2012 ASTM A1073/A1073M-12 Standard Practice for Using Hand Micrometers to Measure the Thickness of Nonmetallic and Metallic-Coated Steel Sheet
