ASTM D2517-18
Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- Standard No.
- ASTM D2517-18
- Release Date
- 2018
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D2517-18(2023)
- Latest
- ASTM D2517-18(2023)
- Scope
- 1.1 This specification covers requirements and methods of test for materials, dimensions and tolerances, hydrostatic-burst strength, chemical resistance, and longitudinal tensile properties, for reinforced epoxy resin pipe and fittings for use in gas mains and services for direct burial and insertion applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas, petroleum fuels (propane–air and propane–butane vapor mixtures), manufactured and mixed gases where resistance to gas permeation, toughness, resistance to corrosion, aging, and deterioration from water, gas, and gas additives are required. Methods of marking are also given. Design considerations are discussed in Appendix X1. 1.2 The values in SI units are to be regarded as the standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.4 A recommended inplant quality control program is given in Appendix X2. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D2517-18 Referenced Document
- ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
- ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
- ASTM D1898
- ASTM D2105 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
- ASTM D2143 Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
- ASTM D2290 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe*， 2019-08-01 Update
- ASTM D2412 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
- ASTM D2924 Standard Test Method for External Pressure Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
- ASTM D2992 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
- ASTM D2996 Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
- ASTM D3567 Standard Practice for Determining Dimensions of ldquo;Fiberglassrdquo; (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
- ASTM D3839 Standard Practice for Underground Installation of "Fiberglass" (Glass-Fiber- Reinforced Thermosetting-Resin) Pipe
- ASTM D3892 Standard Practice for Packaging/Packing of Plastics
- ASTM D396 Standard Specification for Fuel Oils
- ASTM D543 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
- ASTM D5685 Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
- ASTM D618 Standard Practice for Conditioning Plastics for Testing*， 2021-07-15 Update
- ASTM D883 Standard Terminology Relating to Plastics*， 2024-02-01 Update
- ASTM F412 Standard Terminology Relating to Plastic Piping Systems*， 2023-07-20 Update
ASTM D2517-18 history
- 2023 ASTM D2517-18(2023) Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- 2018 ASTM D2517-18 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- 2006 ASTM D2517-06(2011) Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- 2006 ASTM D2517-06 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- 2005 ASTM D2517-05 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- 2000 ASTM D2517-00e1 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
- 2000 ASTM D2517-00 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
