ASTM C1902-22a
Standard Specification for Cellular Glass Insulation Used in Building and Roof Applications
- Standard No.
- ASTM C1902-22a
- Release Date
- 2022
- Published By
- American Society for Testing and Materials (ASTM)
- Latest
- ASTM C1902-22a
- Scope
- 1.1 This specification covers the general requirements for thermal insulation block composed of rigid cellular glass intended for use in building exterior and interior walls, foundation, floor, ceiling, and roofing applications. The insulation blocks are intended for continuous use at temperatures between 200°F and −50°F (93.3°C and −45.6°C). 1.2 This standard is intended to apply to rigid cellular glass thermal insulation block products that are commercially useful in building exterior and interior walls, foundation, floor, ceiling, and roofing construction. For engineering and design purposes, users need to follow specific product information provided by block manufacturers regarding physical properties, system design considerations and installation recommendations. 1.3 The use of thermal insulation materials covered by this specification is typically regulated by building codes, or other agencies that address fire performance or both. Where required, the fire performance of the material shall be addressed through standard fire test methods established by the appropriate governing documents. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. For conversion to metric units other than those contained in this standard, refer to IEEE/ASTM SI 10. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C1902-22a Referenced Document
- ASTM C1045 Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
- ASTM C1617 Standard Practice for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Metals
- ASTM C165 Standard Test Method for Measuring Compressive Properties of Thermal Insulations
- ASTM C168 Standard Terminology Relating to Thermal Insulation
- ASTM C177 Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
- ASTM C203 Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
- ASTM C240 Standard Test Methods of Testing Cellular Glass Insulation Block
- ASTM C303 Standard Test Method for Dimensions and Density of Preformed Block and Broad-Type Thermal Insulation
- ASTM C390 Standard Criteria for Sampling and Acceptance of Preformed Thermal Insulation Lots
- ASTM C518 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
- ASTM D2126 Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging
- ASTM E136 Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750oC
- ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
- ASTM E96/E96M Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials*， 2024-03-01 Update
ASTM C1902-22a history
- 2022 ASTM C1902-22a Standard Specification for Cellular Glass Insulation Used in Building and Roof Applications
- 2022 ASTM C1902-22 Standard Specification for Cellular Glass Insulation Used in Building and Roof Applications
- 2020 ASTM C1902-20 Standard Specification for Cellular Glass Insulation Used in Building and Roof Applications
