ASTM D638-22
Standard Test Method for Tensile Properties of Plastics

Standard No.
ASTM D638-22
Release Date
2022
Published By
American Society for Testing and Materials (ASTM)
Latest
ASTM D638-22
Scope
1.1 This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed. 1.2 This test method is applicable for testing materials of any thickness up to 14 mm (0.55 in.). However, for testing specimens in the form of thin sheeting, including film less than 1.0 mm (0.04 in.) in thickness, ASTM standard D882 is the preferred test method. Materials with a thickness greater than 14 mm (0.55 in.) shall be reduced by machining. 1.3 This test method includes the option of determining Poisson’s ratio at room temperature. NOTE 1—This standard and ISO 527-1 address the same subject matter, but differ in technical content. NOTE 2—This test method is not intended to cover precise physical procedures. It is recognized that the constant rate of crosshead movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate of crosshead movement and rate of strain between gage marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, which are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed. NOTE 3—This test method may be used for testing phenolic molded resin or laminated materials. However, where these materials are used as electrical insulation, such materials should be tested in accordance with Test Methods D229 and Test Method D651. NOTE 4—For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus >20-GPa (>3.0 × 106 -psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M. 1.4 Test data obtained by this test method have been found to be useful in engineering design. However, it is important to consider the precautions and limitations of this method found in Note 2 and Section 4 before considering these data for engineering design. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D638-22 Referenced Document

  • ASTM D1822 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
  • ASTM D229 Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation
  • ASTM D3039/D3039M Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
  • ASTM D4000 Standard Classification System for Specifying Plastic Materials*2023-03-15 Update
  • ASTM D4066 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
  • ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
  • ASTM D5947 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
  • ASTM D618 Standard Practice for Conditioning Plastics for Testing
  • ASTM D882 Standard Test Method for Tensile Properties of Thin Plastic Sheeting
  • ASTM D883 Standard Terminology Relating to Plastics*2024-02-01 Update
  • ASTM E132 Standard Test Method for Poisson''s Ratio at Room Temperature
  • ASTM E2935 Standard Practice for Evaluating Equivalence of Two Testing Processes
  • ASTM E4 Standard Practices for Force Verification of Testing Machines
  • ASTM E456 Standard Terminology for Relating to Quality and Statistics
  • ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
  • ASTM E83 Standard Practice for Verification and Classification of Extensometer
  • ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles

ASTM D638-22 history

  • 2022 ASTM D638-22 Standard Test Method for Tensile Properties of Plastics
  • 2014 ASTM D638-14 Standard Test Method for Tensile Properties of Plastics
  • 2010 ASTM D638-10 Standard Test Method for Tensile Properties of Plastics
  • 2008 ASTM D638-08 Standard Test Method for Tensile Properties of Plastics
  • 2003 ASTM D638-03 Standard Test Method for Tensile Properties of Plastics
  • 2002 ASTM D638-02a Standard Test Method for Tensile Properties of Plastics
  • 2002 ASTM D638-02 Standard Test Method for Tensile Properties of Plastics
  • 2001 ASTM D638-01 Standard Test Method for Tensile Properties of Plastics
  • 2002 ASTM D638-00 Standard Test Method for Tensile Properties of Plastics
  • 1999 ASTM D638-99 Standard Test Method for Tensile Properties of Plastics
Standard Test Method for Tensile Properties of Plastics



Copyright ©2024 All Rights Reserved