ASTM D6276-19
Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization

Standard No.

ASTM D6276-19

Release Date

2019

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D6276-19

Scope

1.1 This test method provides a means for estimating the soil-lime proportion requirement for stabilization of a soil. This test method is performed on soil passing the 425µm (No. 40) sieve. The optimum soil-lime proportion for soil stabilization is determined by tests of specific characteristics of stabilized soil such as unconfined compressive strength or plasticity index. 1.2 Some highly alkaline by-products (lime kiln dust, cement kiln dust, carbide lime, and so forth) have been successfully used to stabilize soil. This test method is not intended for these materials and any such product would need to be tested for specific characteristics as indicated in 1.1. 1.3 This test method is used to determine the percentage of lime that results in a soil-lime pH of approximately 12.4. NOTE 1—Under ideal laboratory conditions of 25°C and sea level elevation, the pH of the lime-soil-water solution should be 12.4. 1.4 Lime is not an effective stabilizing agent for all soils. Some soil components such as sulfates, phosphates, organics, and iron can adversely affect soil-lime reactions and may produce erroneous results using this test method. 1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.6.1 The procedures used to specify how data are collected/ recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis for engineering data. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D6276-19 Referenced Document

• ASTM C977 Standard Specification for Quicklime and Hydrated Lime for Soil Stabilization
• ASTM D1193 Standard Specification for Reagent Water
• ASTM D1293 Standard Test Methods for pH of Water
• ASTM D2216 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
• ASTM D3740 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D421 Standard Practice for Dry Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants
• ASTM D4753 Standard Specification for Evaluating, Selecting, and Specifying Balances and Scales for Use in Soil, Rock, and Construction Materials Testing
• ASTM D6026 Standard Practice for Using Significant Digits in Geotechnical Data
• ASTM D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids
• ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes

ASTM D6276-19 history

• 2019 ASTM D6276-19 Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization
• 1999 ASTM D6276-99a(2006)e1 Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization
• 1999 ASTM D6276-99a(2006) Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization
• 1999 ASTM D6276-99a Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization