ASTM C33/C33M-16e1
Standard Specification for Concrete Aggregates

Standard No.
ASTM C33/C33M-16e1
Release Date
2016
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM C33/C33M-18
Latest
ASTM C33/C33M-23
Scope
1.1 This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete.2 1.2 This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished. NOTE 1—This specification is regarded as adequate to ensure satisfactory materials for most concrete. It is recognized that, for certain work or in certain regions, it may be either more or less restrictive than needed. For example, where aesthetics are important, more restrictive limits may be considered regarding impurities that would stain the concrete surface. The specifier should ascertain that aggregates specified are or can be made available in the area of the work, with regard to grading, physical, or chemical properties, or combination thereof. 1.3 This specification is also for use in project specifications to define the quality of aggregate, the nominal maximum size of the aggregate, and other specific grading requirements. Those responsible for selecting the proportions for the concrete mixture shall have the responsibility of determining the proportions of fine and coarse aggregate and the addition of blending aggregate sizes if required or approved. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.

ASTM C33/C33M-16e1 Referenced Document

  • ASTM C1105 Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
  • ASTM C1157 Standard Performance Specification for Hydraulic Cement*， 2024-04-21 Update
  • ASTM C117 Standard Test Method for Materials Finer than 75-181m (No. 200) Sieve in Mineral Aggregates by Washing
  • ASTM C123 Standard Test Method for Lightweight Particles in Aggregate
  • ASTM C1240 Standard Specification for Silica Fume Used in Cementitious Mixtures*， 2020-01-15 Update
  • ASTM C125 Standard Terminology Relating to Concrete and Concrete Aggregates*， 2021-10-01 Update
  • ASTM C1260 Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method)
  • ASTM C1293 Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
  • ASTM C131 Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine*， 2024-04-21 Update
  • ASTM C136 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
  • ASTM C142 Standard Test Method for Clay Lumps and Friable Particles in Aggregates
  • ASTM C150 Standard Specification for Portland Cement
  • ASTM C1567 Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method)*， 2023-06-01 Update
  • ASTM C227 Standard Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)
  • ASTM C289 Standard Test Method for Potential Alkali-Silica Reactivity of Aggregates (Chemical Method)
  • ASTM C29/C29M Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
  • ASTM C294 Standard Descriptive Nonmenclature for Constituents of Concrete Aggregates
  • ASTM C295 Standard Guide for Petrographic Examination of Aggregates for Concrete
  • ASTM C311 Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete*， 2024-04-21 Update
  • ASTM C330 Standard Specification for Lightweight Aggregates For Structural Concrete
  • ASTM C331 Standard Specification for Lightweight Aggregates for Concrete Masonry Units*， 2024-04-21 Update
  • ASTM C332 Standard Specification for Lightweight Aggregates for Insulating Concrete
  • ASTM C342 
  • ASTM C40 Standard Test Method for Organic Impurities in Fine Aggregates for Concrete
  • ASTM C441 Standard Test Method for Effectiveness of Mineral Admixtures or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction
  • ASTM C535 Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
  • ASTM C586 Standard Test Method for Potential Alkali Reactivity of Carbonate Rocks for Concrete Aggregates (Rock Cylinder Method)
  • ASTM C595 Standard Specification for Blended Hydraulic Cements
  • ASTM C618 Standard Specification for Fly Ash And Raw Or Calcined Natural Pozzolan For Use As A Mineral Admixture In Portland Cement Concrete
  • ASTM C637 Standard Specification for Aggregates for Radiation-Shielding Concrete
  • ASTM C638 Standard Descriptive Nonmenclature of Constituents of Aggregates for Radiation-Shielding Concrete
  • ASTM C666/C666M Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing*， 2024-04-21 Update
  • ASTM C87 Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar
  • ASTM C88 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate
  • ASTM C989 Standard Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
  • ASTM D2419 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
  • ASTM D3665 Standard Practice for Random Sampling of Construction Materials
  • ASTM D422 Standard Test Method for Particle-Size Analysis of Soils
  • ASTM D75 Standard Practice for Sampling Aggregates
  • ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes

ASTM C33/C33M-16e1 history

Standard Specification for Concrete Aggregates


Copyright ©2024 All Rights Reserved