ASTM C196-00(2019)
Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
- Standard No.
- ASTM C196-00(2019)
- Release Date
- 2019
- Published By
- American Society for Testing and Materials (ASTM)
- Latest
- ASTM C196-00(2019)
- Scope
- 1.1 This specification covers expanded or exfoliated vermiculite thermal insulating material in the form of dry cement or plaster, intended to be mixed with a suitable proportion of water, applied as a plastic mass, and dried in place, for use as insulation on surfaces operating at temperatures between 100°F (38°C) and 1800°F (982°C). The cement shall not be used where it will be exposed to combustion conditions, such as the hot face lining of a furnace. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 When the installation or use of thermal insulation materials, accessories and systems, may pose safety or health problems, the manufacturer shall provide the user with appropriate current information regarding any known problems associated with the recommended use of the company’s products. The manufacturer shall also recommend protective measures to be employed in the safe utilization of said products. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C196-00(2019) Referenced Document
- ASTM C1058 Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
- ASTM C163 Standard Practice for Mixing Thermal Insulating Cement Samples
- ASTM C166 Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
- ASTM C168 Standard Terminology Relating to Thermal Insulation*， 2022-05-01 Update
- ASTM C177 Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
- ASTM C353
- ASTM C354 Standard Test Method for Compressive Strength of Thermal Insulating or Finishing Cement (Withdrawn 2002)*， 2021-02-18 Update
- ASTM C356 Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
- ASTM C390 Standard Criteria for Sampling and Acceptance of Preformed Thermal Insulation Lots
- ASTM C405 Standard Practice for Estimating Consistency of Wet-Mixed Thermal Insulating Cement (Withdrawn 2006)
- ASTM C518 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C196-00(2019) history
- 2019 ASTM C196-00(2019) Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
- 2000 ASTM C196-00(2016) Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
- 2000 ASTM C196-00(2010) Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
- 2000 ASTM C196-00(2005) Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
- 2000 ASTM C196-00 Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement
