ASTM E243-18
Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes

Standard No.

ASTM E243-18

Release Date

2018

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM E243-18

Scope

1.1 This practice2 covers the procedures that shall be followed in eddy current examination of copper and copperalloy tubes for detecting discontinuities of a severity likely to cause failure of the tube. These procedures are applicable for tubes with outside diameters to 31⁄8 in. (79.4 mm), inclusive, and wall thicknesses from 0.017 in. (0.432 mm) to 0.120 in. (3.04 mm), inclusive, or as otherwise stated in ASTM product specifications; or by other users of this practice. These procedures may be used for tubes beyond the size range recommended, upon contractual agreement between the purchaser and the manufacturer. 1.2 The procedures described in this practice are based on methods making use of encircling annular examination coil systems. 1.3 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 1—This practice may be used as a guideline for the examination, by means of internal probe examination coil systems, of installations using tubular products where the outer surface of the tube is not accessible. For such applications, the technical differences associated with the use of internal probe coils should be recognized and accommodated. The effect of foreign materials on the tube surface and signals due to tube supports are typical of the factors that must be considered. See E690 for additional details regarding the in-situ examinations using internal probes. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM E243-18 Referenced Document

• ASTM B111/B111M Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock*， 2018-10-01 Update
• ASTM B395/B395M Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes
• ASTM B543 Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube
• ASTM E1316 Standard Terminology for Nondestructive Examinations*， 2024-02-01 Update
• ASTM E543 Standard Practice for Agencies Performing Nondestructive Testing
• ASTM E690 Standard Practice for In Situ Electromagnetic (Eddy-Current) Examination of Nonmagnetic Heat Exchanger Tubes
• ISO 9712 Non-destructive testing — Qualification and certification of NDT personnel*， 2021-12-21 Update

ASTM E243-18 history

• 2018 ASTM E243-18 Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
• 2013 ASTM E243-13 Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
• 2009 ASTM E243-09 Standard Practice for Electromagnetic (Eddy-Current) Examination of Copper and Copper-Alloy Tubes
• 1997 ASTM E243-97(2004)e1 Standard Practice for Electromagnetic (Eddy-Current) Examination of Copper and Copper-Alloy Tubes
• 1997 ASTM E243-97 Standard Practice for Electromagnetic (Eddy-Current) Examination of Copper and Copper-Alloy Tubes