ASTM F2947/F2947M-21a
Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

Standard No.

ASTM F2947/F2947M-21a

Release Date

2021

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F2947/F2947M-21a

Scope

1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 150 to 1500 mm [6 to 60 in.]. 1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an interior liner using a corrugated exterior profile (Fig. 1). 1.4 The products manufactured under this specification use either virgin or recycled (post-industrial or post-consumer) materials in accordance with the requirements specified for each. 1.5 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F2947/F2947M-21a Referenced Document

• ASTM A666 Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar*， 2023-03-01 Update
• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D1603 Standard Test Method for Carbon Black In Olefin Plastics
• ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
• ASTM D2321 Recommended Practice for Underground Installation Of Flexible Thermoplastic Sewer Pipe
• ASTM D2412 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
• ASTM D2444 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
• ASTM D2565 Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
• ASTM D2990 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
• ASTM D3212 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
• ASTM D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials*， 2024-04-21 Update
• ASTM D3895 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
• ASTM D4218 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
• ASTM D4389 Standard Specification for Finished Glass Fabrics Woven From Rovings
• ASTM D4703 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
• ASTM D4883 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
• ASTM D5630 Standard Test Method for Ash Content in Thermoplastics
• ASTM D618 Standard Practice for Conditioning Plastics for Testing
• ASTM D638 Standard Test Method for Tensile Properties of Plastics
• ASTM D6992 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
• ASTM D7399 Standard Test Method for Determination of the Amount of Polypropylene in Polypropylene/Low Density Polyethylene Mixtures Using Infrared Spectrophotometry
• ASTM F2136 Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe*， 2024-02-01 Update
• ASTM F3181 Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE*， 2023-07-01 Update
• ASTM F3308/F3308M Standard Practice for Sampling and Testing Frequency for Recycled Materials in Polyethylene (PE) Pipe for Non-Pressure Applications*， 2023-11-01 Update
• ASTM F412 Standard Terminology Relating to Plastic Piping Systems*， 2023-07-20 Update
• ASTM F477 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
• ASTM G154 Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials*， 2023-01-01 Update
• ASTM G155 Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials*， 2024-04-21 Update
• ISO 15270 Plastics - Guidelines for the recovery and recycling of plastics waste

ASTM F2947/F2947M-21a history

• 2021 ASTM F2947/F2947M-21a Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• 2021 ASTM F2947/F2947M-21 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• 2020 ASTM F2947/F2947M-20 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• 2019 ASTM F2947/F2947M-19 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• 2014 ASTM F2947/F2947M-14 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• 2012 ASTM F2947-12e1 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• 2012 ASTM F2947-12 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications