ASTM F1387-19
Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

Standard No.

ASTM F1387-19

Release Date

2019

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM F1387-23

Latest

ASTM F1387-23

Scope

1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process. 1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole. 1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein. 1.4 The tests specified in Section 13 and described in Annex A1 and the Supplementary Requirements Section are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products. 1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Requirements Section and the annexes of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F1387-19 Referenced Document

• ANSI/ASQ Z1.4 Sampling Procedures and Tables for Inspection by Attributes
• ANSI/NCSL Z540 U.S. Guide to the Expression of Uncertainty in Measurement
• ASTM A1016/A1016M Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes*， 2023-11-01 Update
• ASTM A106/A106M Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service*， 2019-11-01 Update
• ASTM A108 Standard Specification for Steel Bars, Carbon, Cold-Finished, Standard Quality
• ASTM A109/A109M Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• ASTM A167 Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip
• ASTM A182/A182M Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
• ASTM A213/A213M Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
• ASTM A234/A234M Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
• ASTM A240/A240M Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
• ASTM A249/A249M Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
• ASTM A262 Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
• ASTM A269 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service*， 2024-04-20 Update
• ASTM A276 Standard Specification for Stainless Steel Bars and Shapes
• ASTM A312/A312M Standard Specification for Seamless and Welded Austenitic Stainless Steel Pipes
• ASTM A335/A335M Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
• ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
• ASTM A380 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
• ASTM A403/A403M Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings
• ASTM A450/A450M Standard Specification for General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel Tubes
• ASTM A479/A479M Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels*， 2023-06-09 Update
• ASTM A53 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
• ASTM A530/A530M Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
• ASTM A564/A564M Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
• ASTM A576 Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality
• ASTM A967 Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts
• ASTM A999/A999M Standard Specification for General Requirements for Alloy and Stainless Steel Pipe
• ASTM B111/B111M Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
• ASTM B117 Standard Practice for Operating Salt Spray (Fog) Apparatus
• ASTM B121/B121M Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar
• ASTM B122/B122M Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
• ASTM B124/B124M Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes*， 2020-04-01 Update
• ASTM B154 Standard Test Method for Mercurous Nitrate Test for Copper and Copper Alloys
• ASTM B16/B16M Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines*， 2019-10-01 Update
• ASTM B164 Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
• ASTM B21/B21M Standard Specification for Naval Brass Rod, Bar, and Shapes*， 2024-04-20 Update
• ASTM B251/B251M Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube*， 2024-04-20 Update
• ASTM B36/B36M Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• ASTM B369 Standard Specification for Copper-Nickel Alloy Castings
• ASTM B371/B371M Standard Specification for Copper-Zinc-Silicon Alloy Rod
• ASTM B564 Standard Specification for Nickel Alloy Forgings*， 2022-04-01 Update
• ASTM B633 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
• ASTM B696 Standard Specification for Coatings of Cadmium Mechanically Deposited*， 2023-05-01 Update
• ASTM B75/B75M Standard Specification for Seamless Copper Tube*， 2020-04-01 Update
• ASTM B766 Standard Specification for Electrodeposited Coatings of Cadmium
• ASTM B88 Standard Specification for Seamless Copper Water Tube
• ASTM E1529 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies*， 2022-04-01 Update
• ASTM E511 Standard Test Method for Measuring Heat Flux Using a Copper-Constantan Circular Foil, Heat-Flux Gage
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials*， 2024-01-01 Update
• SAE 1010 Standard Practice for Manpower and Personnel*， 2020-09-18 Update
• SAE AMS2243 TOLERANCES Stainless Steel Seamless Tubing
• SAE AMS5643 STEEL, BARS AND FORGINGS, CORROSION RESISTANT 17Cr - 4.5Ni - 4Cu Precipitation Hardening
• SAE J514 Metallic Connections for Fluid Power and General Use - Part 3: NPTF Pipe Adapters and NPSM Adapter Unions*， 2023-12-01 Update
• SAE J515 Specification for O-Ring Materials Used with Hydraulic Connectors*， 2022-05-26 Update

ASTM F1387-19 history

• 2023 ASTM F1387-23 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• 2019 ASTM F1387-19 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• 1999 ASTM F1387-99(2012) Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• 1999 ASTM F1387-99(2005) Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• 1999 ASTM F1387-99 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• 1998 ASTM F1387-93(1998) Standard Specification for Performance of Mechanically Attached Fittings