ASTM F712-06(2018)
Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers

Standard No.

ASTM F712-06(2018)

Release Date

2018

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F712-06(2018)

Scope

1.1 These test methods cover three electrical tests on plastic guards and assembled guard systems. They are: 1.1.1 Method A—Withstand voltage proof test, 1.1.2 Method B—Flashover voltage, and 1.1.3 Method C—Leakage current. 1.1.4 This specification covers plastic guard equipment and guard systems used by workers for temporary insulation on electric power circuits. 1.1.5 Plastic guard equipment covered by this specification is rated for momentary, or brush contact only. Maximum-use voltages are covered in Table 1 and Table 2. 1.2 These test methods cover, but are not limited to, the following typical guards: 1.2.1 Conductor Guards and Connecting Covers as follows: 1.2.1.1 Line guards, 1.2.1.2 Line guard connectors, 1.2.1.3 Insulator covers, 1.2.1.4 Dead-end covers, 1.2.1.5 Bus guards, and 1.2.1.6 Bus “T” guards. 1.2.2 Structure and Apparatus Covers as follows: 1.2.2.1 Pole guards, 1.2.2.2 Ridge pin covers, 1.2.2.3 Switch blade covers, 1.2.2.4 Arm guards, 1.2.2.5 Cutout covers, 1.2.2.6 Structural barriers, and 1.2.2.7 Cross arm guard. 1.3 It is common practice for the user of this equipment to prepare instructions for the correct use and maintenance. 1.4 The use and maintenance of this equipment is beyond the scope of these test methods. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F712-06(2018) Referenced Document

• ASTM D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
• ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics*， 2023-03-15 Update
• ASTM D570 Standard Test Method for Water Absorption of Plastics*， 2018-08-01 Update
• IEEE 978 Guide for in-Service Maintenance and Electrical Testing of Live-Line Tools

ASTM F712-06(2018) history

• 2018 ASTM F712-06(2018) Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers
• 2006 ASTM F712-06(2011) Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers
• 2006 ASTM F712-06 Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers
• 1988 ASTM F712-88(2000) Standard Test Methods for Electrically Insulating Plastic Guard Equipment for Protection of Workers
• 2000 ASTM F712-88(1995) Standard Test Methods for Electrically Insulating Plastic Guard Equipment for Protection of Workers