ASTM D6622/D6622M-20
Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems

Standard No.

ASTM D6622/D6622M-20

Release Date

2020

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D6622/D6622M-20

Scope

1.1 This guide covers the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces. 1.2 For the purpose of this guide, the substrate is assumed to be concrete or masonry, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, and overburden are beyond the scope of this guide. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D6622/D6622M-20 Referenced Document

• ASTM C981 Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks
• ASTM D1079 Standard Terminology Relating to Roofing and Waterproofing
• ASTM D1327/D1327M Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing
• ASTM D1668/D1668M Standard Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing*， 2024-04-20 Update
• ASTM D173/D173M Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing
• ASTM D2178/D2178M Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing*， 2024-04-20 Update
• ASTM D226/D226M Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing*， 2023-02-01 Update
• ASTM D227/D227M Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing
• ASTM D41/D41M Standard Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing*， 2023-07-01 Update
• ASTM D43/D43M Standard Specification for Coal Tar Primer Used in Roofing, Dampproofing, and Waterproofing
• ASTM D449/D449M Standard Specification for Asphalt Used in Dampproofing and Waterproofing*， 2024-04-20 Update
• ASTM D450/D450M Standard Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing
• ASTM D4586/D4586M Standard Specification for Asphalt Roof Cement, Asbestos-Free
• ASTM D4990 Standard Specification for Coal-Tar Glass Felt Used in Roofing and Waterproofing
• ASTM D5295/D5295M Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
• ASTM D5643/D5643M Standard Specification for Coal Tar Roof Cement, Asbestos Free
• ASTM D5898/D5898M Standard Guide for Standard Details for Adhered Sheet Waterproofing*， 2021-12-01 Update
• ASTM D5957 Standard Guide for Flood Testing Horizontal Waterproofing Installations*， 2021-12-01 Update
• ASTM D6152/D6152M Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing
• ASTM D6162/D6162M Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements*， 2021-12-01 Update
• ASTM D6163/D6163M Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements*， 2021-12-01 Update
• ASTM D6164/D6164M Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements*， 2021-12-01 Update
• ASTM D6451/D6451M Standard Guide for Application of Asphalt-Based Protection Board*， 2021-12-01 Update
• ASTM D6506/D6506M Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

ASTM D6622/D6622M-20 history

• 2020 ASTM D6622/D6622M-20 Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
• 2018 ASTM D6622/D6622M-01(2018)e1 Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
• 2001 ASTM D6622-01(2009) Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
• 2001 ASTM D6622-01 Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems