ASTM E1888/E1888M-17 Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
1.1 This practice covers guidelines for acoustic emission (AE) examinations of pressurized containers made of fiberglass reinforced plastic (FRP) with balsa cores. Containers of this type are commonly used on tank trailers for the transport of hazardous chemicals.
1.2 This practice is limited to cylindrical shape containers,
0.5 m [20 in.] to 3 m [120 in.] in diameter, of sandwich construction with balsa wood core and over 30 % glass (by weight) FRP skins. Reinforcing material may be mat, roving, cloth, unidirectional layers, or a combination thereof. There is no restriction with regard to fabrication technique or method of design.
1.3 This practice is limited to containers that are designed for less than
0.520 MPa [75.4 psi] (gage) above static pressure head due to contents.
1.4 This practice does not specify a time interval between examinations for re-qualification of a pressure container.
1.5 This practice is used to determine if a container is suitable for service or if follow-up NDT is needed before that determination can be made.
1.6 Containers that operate with a vacuum are not within the scope of this practice.
1.7 Repair procedures are not within the scope of this practice.
1.8 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E1888/E1888M-17 Referenced Document
ASTM E1067 Standard Practice for Acoustic Emission Examination of Fiberglass Reinforced Plastic Resin (FRP) Tanks/Vessels
ASTM E1106 Standard Method for Primary Calibration of Acoustic Emission Sensors
ASTM E1316 Standard Terminology for Nondestructive Examinations*, 2024-02-01 Update
ASTM E1781 Standard Practice for Secondary Calibration of Acoustic Emission Sensors
ASTM E2374 Standard Guide for Acoustic Emission System Performance Verification*, 2021-11-01 Update
ASTM E543 Standard Practice for Agencies Performing Nondestructive Testing
ASTM E976 Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response*, 2021-11-01 Update
ISO 9712 Non-destructive testing — Qualification and certification of NDT personnel*, 2021-12-21 Update
ASTM E1888/E1888M-17 history
2017ASTM E1888/E1888M-17 Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
2012ASTM E1888/E1888M-12 Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
2007ASTM E1888/E1888M-07 Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
2002ASTM E1888/E1888M-02 Standard Test Method for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
1997ASTM E1888-97 Standard Test Method for Acoustic Emission Testing of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores