ASTM F1667/F1667M-21a
Standard Specification for Driven Fasteners: Nails, Spikes, and Staples

Standard No.

ASTM F1667/F1667M-21a

Release Date

2021

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F1667/F1667M-21a

Scope

1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. NOTE 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–63. 1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. 1.3 This specification is applicable in either inch-pounds (F1667) or SI units [F1667M]. Values stated in SI are a mathematical conversion to two significant digits and are shown in brackets [ ]. 1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F1667/F1667M-21a Referenced Document

• ASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware*， 2023-05-16 Update
• ASTM A641/A641M Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire
• ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
• ASTM C1063 Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
• ASTM C1861 Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster*， 2023-10-01 Update
• ASTM C514 Standard Specification for Nails for the Application of Gypsum Board
• ASTM F1575/F1575M Standard Test Method for Determining Bending Yield Moment of Nails, Spikes, and Dowel-type Threaded Fasteners*， 2024-03-20 Update
• ASTM F3359/F3359M Standard Test Method for Determining Bending Yield Moment of Staples
• ASTM F547 Standard Terminology of Nails for Use with Wood and Wood-Base Materials
• ASTM F592 Standard Terminology of Collated and Cohered Fasteners and Their Application Tools
• ASTM F680 Standard Test Methods for Nails

ASTM F1667/F1667M-21a history

• 2021 ASTM F1667/F1667M-21a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2021 ASTM F1667-21 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2020 ASTM F1667-20 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2018 ASTM F1667-18a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2018 ASTM F1667-18 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2017 ASTM F1667-17 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2015 ASTM F1667-15 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2013 ASTM F1667-13 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2011 ASTM F1667-11ae1 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2011 ASTM F1667-11a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2011 ASTM F1667-11 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2010 ASTM F1667-10 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2005 ASTM F1667-05 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2003 ASTM F1667-03 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2002 ASTM F1667-02a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2002 ASTM F1667-02 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2001 ASTM F1667-01a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2001 ASTM F1667-01 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• 2000 ASTM F1667-00 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples