ASTM F959/F959M-17 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series
1.1 This specification covers the requirements for compressible-washer-type direct tension indicators, (DTIs) capable of indicating the achievement of a specified minimum tension in a structural bolting assembly.
1.2 Eight types of DTIs in nominal diameter sizes 1⁄2 through 1 1⁄2 in. as well as M16 through M36 are covered:
1.2.1 Type 325-1—DTIs for use with Specification F3125 Grade A325 Type 1 bolts or Grade F1852 assemblies.
1.2.2 Type 325–3—DTIs for use with Specification F3125 Grade A325 Type 3 bolts or Grade F1852 Type 3 assemblies.
1.2.3 Type 490–1—DTIs for use with Specification F3125 Grade A490 Type 1 bolts or Grade F2280 assemblies.
1.2.4 Type 490–3—DTIs for use with Specification F3125 Grade A490 Type 3 bolts Grade F2280 Type 3 assemblies.
1.2.5 Type
8.8-1—DTIs for use with Specification F3125 Grade A325M Type 1 bolts.
1.2.6 Type
8.8-3—DTIs for use with Specification F3125 Grade A325M Type 3 bolts.
1.2.7 Type 10.9-1—DTIs for use with Specification F3125 Grade A490M Type 1 bolts.
1.2.8 Type 10.9-3—DTIs for use with Specification F3125 Grade A490M Type 3 bolts.
1.3 DTIs are intended for installation with the protrusions against a hardened surface such as a bolt head, a hardened nut, or a hardened washer. (See Research Council on Structural Connections: Specification for Structural Joints Using High–Strength Bolts.)
1.4 This specification provides for furnishing Type 3 DTIs to a Chemical Composition Requirement or a Corrosion Resistance Index (CRI) at the manufacturer’s discretion.
1.5 Terms used in this specification are defined in Terminology F1789 unless otherwise specified.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7 The following precautionary statement pertains only to the test method portions, Section 10 and Appendix X1 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F959/F959M-17 Referenced Document
ASME B18.2.6 Fasteners for Use in Structural Applications*, 2019-03-29 Update
ASTM A1059/A1059M Standard Specification for Zinc Alloy Thermo-Diffusion Coatings (TDC) on Steel Fasteners, Hardware, and Other Products*, 2018-11-01 Update
ASTM A325 Standard Specification for High-Strength Bolts For Structural Steel Joints
ASTM A325M Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength &40;Metric&41;*, 2024-04-20 Update
ASTM A490 Standard Specification for Quenched And Tempered Alloy Steel Bolts For Structural Steel Joints
ASTM A490M Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric) *, 2024-04-20 Update
ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel*, 2021-11-01 Update
ASTM F1470 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection*, 2024-01-26 Update
ASTM F1789 Standard Terminology for F16 Mechanical Fasteners*, 2023-11-01 Update
ASTM F1852 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength*, 2024-04-20 Update
ASTM F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength*, 2024-04-20 Update
ASTM F3125 Standard Specification for High Strength Structural Bolts, Steel and Alloy Steel, Heat Treated, 120 ksi (830 MPa) and 150 ksi (1040 MPa) Minimum Tensile Strength, Inch and Metric Dimensions*, 2024-04-20 Update
ASTM F436/F436M Standard Specification for Hardened Steel Washers Inch and Metric Dimensions*, 2019-12-01 Update
ASTM F606/F606M Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets*, 2021-06-01 Update
ASTM G101 Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
ASTM F959/F959M-17 history
2023ASTM F959/F959M-17a(2023) Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series
2017ASTM F959/F959M-17a Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series
2017ASTM F959/F959M-17 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series
2015ASTM F959-15 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2013ASTM F959-13 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2009ASTM F959-09 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2007ASTM F959-07a Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2007ASTM F959-07 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2006ASTM F959-06 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2005ASTM F959-05a Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2005ASTM F959-05 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2004ASTM F959-04 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2002ASTM F959-02 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2001ASTM F959-01a Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2001ASTM F959-01 Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
2002ASTM F959-99a Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners