BS EN 12201-3:2024
Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE) - Fittings
- Standard No.
- BS EN 12201-3:2024
- Release Date
- 2024
- Published By
- British Standards Institution (BSI) GB / BSI
- Latest
- BS EN 12201-3:2024
- Scope
- 1 Scope This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application. NOTE 1 For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to subclause 6.6 of this document. Components manufactured for water for other purposes, drains and sewers, and vacuum sewer systems are possibly not suitable for water supply for human consumption. NOTE 2 Industrial application is covered by EN ISO 15494 [4]. The intended uses include sea outfalls, laid in water and pipes suspended below bridges. It also specifies the test parameters for the test methods referred to in this document. In conjunction with EN 12201‑1, EN 12201‑2, EN 12201‑4 and EN 12201‑5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar 1 ; ...
BS EN 12201-3:2024 Referenced Document
- EN 12201-1:2024 Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 1: General
- EN 12201-2:2024 Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 2: Pipes
- EN 12201-5 Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
- EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
- EN ISO 1133-1 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2022)
- EN ISO 11357-6 Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6:2025)*， 2025-06-18 Update
- EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
- EN ISO 1167-3 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007)
- EN ISO 1167-4 Thermoplastics pipes@ fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies
- EN ISO 3126 Plastics piping systems - Plastics components - Determination of dimensions ISO 3126:2005
- ISO 12176-5 Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 5: Two-dimensional data coding of components and data exchange format for PE piping systems
- ISO 13950 Plastics pipes and fittings - Automatic recognition systems for electrofusion joints; Technical Corrigendum 1
- ISO 13951 Plastics piping systems - Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
- ISO 13953 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint — Amendment 1
- ISO 13954 Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm*， 2025-11-19 Update
- ISO 13955 Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies — Amendment 1
- ISO 13956 Plastics pipes and fittings - Decohesion test of polyethylene (PE) saddle fusion joints - Evaluation of ductility of fusion joint interface by tear test*， 2025-11-01 Update
- ISO 13957 Plastics pipes and fittings - Polyethylene (PE) tapping tees - Test method for impact resistance
- ISO 17885:2021 Plastics piping systems - Mechanical fittings for pressure piping systems - Specifications
- ISO 18488 Polyethylene (PE) materials for piping systems — Determination of strain hardening modulus in relation to slow crack growth — Test method*， 2025-10-14 Update
- ISO 4433-1 Thermoplastics pipes - Resistance to liquid chemicals - Classification - Part 1: Immersion test method
- ISO 4433-2 Thermoplastics pipes - Resistance to liquid chemicals - Classification - Part 2: Polyolefin pipes
- ISO 9624 Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions — Amendment 1
BS EN 12201-3:2024 history
- 2024 BS EN 12201-3:2024 Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE) - Fittings
- 0000 BS EN 12201-3:2011+A1:2012(2013)
- 2011 BS EN 12201-3:2011+A1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fittings
- 2011 BS EN 12201-3:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fittings
- 2003 BS EN 12201-3:2003 Plastic piping systems for water supply - Polyethylene (PE) - Fittings
