BS EN 15091:2024
Sanitary tapware. Electronic opening and closing sanitary tapware

Standard No.

BS EN 15091:2024

Release Date

2024

Published By

British Standards Institution (BSI)

Latest

BS EN 15091:2024

---

Scope

The purpose of this document is to specify requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically. The conditions of use for the supply system type are specified in Table 2: Table 2 — Conditions of use Water supply system Limits of use Recommended limits of operation Tapware with normally open or normally closed (monostable) solenoid valves Tapware with latching (bistable) solenoid valves Tapware with normally open or normally closed (monostable) solenoid valves Tapware with latching (bistable) solenoid valves Type 1 (see Figure 1) Minimum dynamic pressure 0,05 MPa (0,5 bar) 0,05 MPa (0,5 bar) (0,1 to 0,5) MPa [(1 to 5) bar] (0,1 to 0,5) MPa [(1 to 5) bar] Maximum static pressure (10 bar) Type 2a (see Figure 2) Minimum dynamic pressure 0,01 MPa (0,1 bar) 0,01 MPa (0,1 bar) (0,01 to 0,2) MPa [(0,1 to 2) bar] (0,01 to 0,2) MPa [(0,1 to 2) bar] Maximum static pressure (10 bar) Temperature of the water ≤ 75 °C ≤ 75 °C ≤ 65 °C ≤ 65 °C a For Type 2, the manufacturer is expected to declare the minimum operating pressure at which opening, closing and the specified flow rate can be obtained. There is usually no acoustic classification for tapware used in supply systems of Type 2 and no specifications governing the level of noise emissions from these water installations. If supply pressures are such that excessive noise is generated it is advised that pressure or flow regulators are fitted in the system. Or where practicable, tapware conforming to the appropriate acoustic classification are used. Annex B lists possible consequences of using a product outside its recommended operating range.

BS EN 15091:2024 Referenced Document

• EN 12541:2002 Sanitary tapware Pressure flushing valves and automatic closing urinal valves PN 10*， 2025-02-28 Update
• EN 13618 Flexible hose assemblies in drinking water installations - Functional requirements and test methods
• EN 13959 Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D*， 2025-02-28 Update
• EN 1717 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow*， 2025-02-28 Update
• EN 246 Sanitary tapware - General specifications for flow rate regulators
• EN 248 Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr*， 2025-02-28 Update
• EN 31 Wash basins - Connecting dimensions
• EN 35 Pedestal and wall-hung bidets with over-rim supply - Connecting dimensions
• EN 60335-1 Household and similar electrical appliances - Safety - Part 1: General requirements
• EN 60529 Degrees of protection provided by enclosures (lP Code)(IEC 60529:1989)
• EN 61000-6-3 Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
• EN 695 Kitchen Sinks - Connecting Dimensions
• EN 997 WC pans and WC suites with integral trap
• EN IEC 60730-2-8 Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
• EN IEC 61000-6-1 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential@ commercial and light-industrial environments
• EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation ISO 228-1: 2000
• EN ISO 3822-1 Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement - Amendment 1: Measurement uncertainty (ISO 3822-1:1999/Amd 1:2008)
• EN ISO 3822-2 Acoustics - Laboratory Tests on Noise Emission from Appliances and Equipment Used in Water Supply Installations - Part 2: Mounting and Operating Conditions for Draw-Off Taps and Mixing Valves (ISO 3822-2 : 1995)
• EN ISO 3822-4 Acoustics - Laboratory Tests on Noise Emission from Appliances and Equipment Used in Water Supply Installations - Part 4: Mounting and Operating Conditions for Special Appliances
• EN ISO 5167-1 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2022)

BS EN 15091:2024 history

• 2024 BS EN 15091:2024 Sanitary tapware. Electronic opening and closing sanitary tapware
• 2013 BS EN 15091:2013 Sanitary tapware. Electronic opening and closing sanitary tapware
• 2007 BS EN 15091:2006 Sanitary tapware - Electronic opening and closing sanitary tapware

Topics on standards and specifications

Standard and Specification